# moldtraining.us/free-training/mold-inspection-process/: agent-readable view

The Mold Inspection Process: From Interview to Report (free lesson 10 of 12)
type        free mini-training lesson with 8-question quiz (graded in-browser, nothing saved)
time        14 minutes
summary     Free lesson on how a professional mold inspection works: scope and interview, exterior and interior walkthrough, moisture mapping, HVAC, sampling decisions, and writing a clear, defensible report. 8-question quiz.

objectives
- Plan an inspection scope from the client interview
- Conduct a systematic exterior and interior walkthrough
- Map moisture and document findings with photos and readings
- Write a report with findings, causes and recommendations

sections
- 1. Scope and interview
- 2. Exterior walkthrough
- 3. Interior walkthrough
- 4. Moisture mapping
- 5. HVAC
- 6. Sampling decisions
- 7. The report
- Key takeaways

standards   EPA mold guidance; industry inspection standards of practice

certificate course  https://moldtraining.us/mold-inspector-certification/
note        Free general education based on EPA and CDC mold guidance and OSHA worker-safety principles. It is not an EPA or OSHA certification or a state mold license, not medical or legal advice, and it does not issue a certificate. Nothing you enter on this page is saved or sent.

Courses delivered by HAZWOPER OSHA Training, LLC, an IACET Accredited ProviderDelivered by an IACET Accredited Provider

Leer en espaƱol

Free Mini-Training · Lesson 10 of 12

The Mold Inspection Process: From Interview to Report

A good mold inspection finds the water, documents the damage and gives clear next steps. Learn the sequence professional inspectors follow and what belongs in the report.

  • 14 min
  • 8-question quiz
  • Intermediate
  • Free · no sign-up
On this page
  1. What you'll learn
  2. 1. Scope and interview
  3. 2. Exterior walkthrough
  4. 3. Interior walkthrough
  5. 4. Moisture mapping
  6. 5. HVAC
  7. 6. Sampling decisions
  8. 7. The report
  9. Key takeaways
  10. Lesson quiz

In this lesson

What you'll learn

  • Plan an inspection scope from the client interview
  • Conduct a systematic exterior and interior walkthrough
  • Map moisture and document findings with photos and readings
  • Write a report with findings, causes and recommendations

A mold inspection is a moisture investigation first. Visible growth tells you where the problem showed up; the inspector's job is to find why, how far it extends, and what to do. Organizations such as IAC2 publish mold inspection standards of practice that many inspectors follow, and some states license mold assessors. See state requirements.

1. Scope and interview

Before entering, find out:

  • The reason for the inspection: odor, visible growth, leak history, health concerns, real estate transaction, post-remediation.
  • History: leaks, floods, plumbing or roof repairs, prior mold work, renovations.
  • Occupants: anyone with asthma, allergies or immune conditions.
  • What the client expects: visual only, sampling, a remediation scope.

Agree on the scope and limitations in writing, including areas that won't be accessed.

2. Exterior walkthrough

Water usually starts outside. Check:

  • Roof coverings, flashing, gutters and downspouts.
  • Grading and drainage toward or away from the foundation.
  • Siding, window and door seals, penetrations and sprinkler overspray.
  • Crawl space vents and foundation cracks.

3. Interior walkthrough

Work room by room in a consistent pattern:

  • Look for visible growth, water stains, peeling paint, warped materials and efflorescence.
  • Note musty odors and where they're strongest.
  • Check wet rooms: bathrooms, kitchens, laundry, water heater and under sinks.
  • Check attics, basements and crawl spaces. See crawl space and attic mold.

4. Moisture mapping

  • Measure room temperature and relative humidity with a hygrometer, and compare with outdoors.
  • Use a moisture meter on walls, floors, ceilings and cabinets near suspected sources, and map wet areas.
  • Use a thermal camera to scan for anomalies, then confirm with a moisture meter.
  • Note dew point conditions where condensation is suspected. See the dew point calculator.

5. HVAC

Inspect accessible components: air handler, coils, drip pans and condensate lines, filters and supply registers. Note visible growth, standing water and dirty filters. Don't open sealed systems beyond your scope.

6. Sampling decisions

Decide whether sampling adds value. EPA says it usually isn't needed when growth is visible. If sampling is in scope, follow a written protocol with controls, as covered in sampling and testing.

7. The report

A clear, defensible report includes:

  • Scope, limitations and conditions at the time of inspection (weather, occupancy).
  • Findings by location, with photos, moisture readings and approximate area of visible growth.
  • Probable moisture sources and contributing conditions.
  • Sampling results and how they were interpreted, if sampling was done.
  • Recommendations: moisture repairs, remediation approach consistent with EPA's size guidance, containment and PPE considerations, and post-remediation verification.

Key takeaways

  • A mold inspection is a moisture investigation.
  • Interview, then inspect the exterior, interior, attics, crawl spaces and HVAC systematically.
  • Map moisture with meters and confirm thermal camera findings.
  • Sample only when it adds value, following a written protocol.
  • Report findings, causes and clear recommendations with photos and readings.

Knowledge check

Lesson 10 quiz: 8 questions

Choose one answer for each question, then select Check my answers. Score 80% or higher to pass. Your answers stay in your browser and are never saved.

Question 1 What is the primary focus of a mold inspection?
Question 2 Why start with an exterior walkthrough?
Question 3 What should be done after a thermal camera shows a cool spot on a wall?
Question 4 Which item belongs in a mold inspection report?
Question 5 According to EPA, when growth is visible, sampling is:
Question 6 Why does the client interview matter?
Question 7 Which HVAC component commonly holds water that supports mold?
Question 8 Why do many professionals separate mold inspection from remediation?

Sources and official references

Last reviewed: October 25, 2026 · Free general education based on EPA and CDC mold guidance and OSHA worker-safety principles. It is not an EPA or OSHA certification or a state mold license, not medical or legal advice, and it does not issue a certificate. Nothing you enter on this page is saved or sent.

Need Documented Mold Training?

Mold Awareness, Property Management and Mold Inspector courses. Certificate of completion. English & Spanish.